• PRODUCT CODE : 75037U
  • NORMS AND LABELS : :
    EC 1Plus-R anglais
    Habitat sain A+ (décret 2011-321)
  • TECHNICAL DATA SHEET : show (fr)
  • SAFETY DATA SHEET according to Regulation 1272/2008/EC (CLP) : show sur inscription (fr)
  • TECHNICAL DATA SHEET : show (en)
  • SAFETY DATA SHEET according to Regulation 1272/2008/EC (CLP) : show sur inscription (en)

EMFIPARQUET PRO PLUS

EMFIPARQUET PRO PLUS is a single component elastomeric adhesive curing under the effect of atmospheric or substrate moisture.
EMFIPARQUET PRO PLUS is a flexible adhesive which meets requirements of NF EN 14293 standard.
Its classification EMICODE EC 1PLUS-R according to EMICODE and A+ according to French decree n° 2011-321 guarantees a very low emission of VOC.
EMFIPARQUET PRO PLUS obtained a proficiency testing performance report from FCBA (French Wood and Furniture Technical Centre) for the bonding of wooden parquet floors made according to standard NF B 54-008 and bonded according to standard NF P 63-202 (DTU 51.2) :
n° FCBA.IBC.342.371-ChD/SM-N°2012.099.356 (massive oak up to 20 x 200 mm)

APPLICATION AREAS

EMFIPARQUET PRO PLUS is designed for bonding in full surface of all types of massive parquet floors even of large dimensions (up to 20 x 200 mm), or for engineered parquet.
For massive parquets of large dimensions, long, wide and thick floorboards, a special attention must be paid during the laying. For the durability of the floor, a good contact between the glue and the parquet must be assured, therefore a higher quantity of adhesive and a load on concerned areas must be applied up to full polymerization of the adhesive.
Adhesion of EMFIPARQUET PRO PLUS is excellent without primer to most substrates such as wood, water-repellent chipboard, concrete or anhydrite screeds, adhering paints, paving, stone.
The application is easy and is not aggressive to varnish.
EMFIPARQUET PRO PLUS remains soft after polymerisation, improving the acoustic comfort of parquets.
Thanks to its excellent moisture and heat resistance, this adhesive is convenient for the laying of parquet in difficult environments (heating floors, bathrooms, etc.)
For heating floors, it must be applied in full surface. In this case, EMFIPARQUET PRO PLUS is convenient for massive parquets up to 20 mm thickness and 200 mm width (with a 0.24 mm maximum warping) and for engineered parquets.
For very wide ROUGH massive parquets (> 140 mm), it is necessary to put weights (approx. 30 kg every other 4 m²) to assure a perfect contact between the parquet and the substrate up to the final setting of the glue (48 h at 20 °C).
EMFIPARQUET PRO PLUS is suited for use with reversible air conditioning systems (heating and cooling floors) under the reserve of guarantee of the manufacturer of parquet.

MANUAL

For substrate preparation and application, refer to DTU 51.2 (standard NF P 63-202)
Substrate preparation :
The substrates must be clean, dry, free of dust and grease. Paving or flooring should not in any way be likely to expose parquet to rising or seepage of moisture.
Do not work at temperatures below 5 °C or when the relative humidity exceeds 65 %.
If necessary, heat and ventilate the room.
The surface should be even (maximum tolerance : 5 mm under a 2 m ruler).
The humidity of the parquet flooring should be between 7 and 11 %.
Substrate humidity level: < 3 % (< 0.5 % for anhydrite screeds).
On anhydrite screeds, it is necessary to rub down beforehand.
On heating floors, after 2 to 3 weeks of functioning, heating has to be stopped 48 h before working. Wait minimum 7 days before turning on heating gradually.
On difficult substrates (contact us) apply epoxy primer EMFIPRIM EPOXY with a roller before laying parquet or before levelling with self-levelling P3 compound.
Application :
Uniformly spread onto the subfloor with an appropriate spatula. Lay the wood lathes into the wet adhesive film. Check the proper transfer on the lath back side.
Respect a gap of 10 to 20 mm all along the walls.
Do not walk on the parquet floor for 12 hours.
Allow to dry for at least 48 hours before sanding.
Cork or fibered underlayers :
Underlayers can be laid with EMFIPARQUET PRO PLUS.
In order to accelerate the adhesive curing, it is convenient to wet the back side of the underlayer with a water spray (ca. 20 g/m²).
Wait until hardening before laying parquet as indicated above.
Cleaning :
Tools should be cleaned with solution EMFINET 683 or with EMFICLEAN AL cloth before the adhesive has completely cured. After curing, mechanical cleaning is required.